Wednesday, June 29, 2011

Packet Tracer configure RIP


Configuring RIP
Topology Diagram



Objectives

·         Configure routers using basic interface configuration commands.
·         Enable RIP.
·         Verify the RIP configuration.

Background / Preparation
A simple routed network has been set up to assist in reviewing RIP routing behavior. In this activity, you will configure RIP across the network and set up end devices to communicate on the network.
Step 1: Configure the SVC01 router and enable RIP.
a.     From the CLI, configure interface Fast Ethernet 0/0 using the IP address 10.0.0.254 /8.
b.    Configure interface serial 0/0/0 using the first usable IP address in network 192.168.1.0 /24 to connect to the RTR01 router. Set the clock rate at 64000.
c.     Configure interface serial 0/0/1 using the first usable IP address in network 192.168.2.0 /24 with a clock rate of 64000.
d.    Using the no shutdown command, enable the configured interfaces.
e.     Configure RIP to advertise the networks for the configured interfaces.
f.     Configure the end devices.
·         Server0 uses the first usable IP address in network 10.0.0.0 /8. Specify the appropriate default gateway and subnet mask.

·         Printer0 uses the second usable IP address in network 10.0.0.0 /8. Specify the appropriate default gateway and subnet mask.

Step 2: Configure the RTR01 router and enable RIP.

a.     Configure interface Fast Ethernet 0/0 using the first usable IP address in network 192.168.0.0 /24 to connect to the RTR02 router.

b.    Configure interface serial 0/0/0 using the second usable IP address in network 192.168.1.0 /24 to connect to the SVC01 router.

c.     Configure interface Fast Ethernet 0/1 using the IP address 172.16.254.254 /16.

d.    Using the no shutdown command, enable the configured interfaces.

e.     Configure RIP to advertise the networks for the configured interfaces.

f.     Configure the end devices.

·         PC0 uses the first usable IP addresses in network 172.16.0.0 /16.

·         PC1 uses the second usable IP address in network 172.16.0.0 /16.

·         Specify the appropriate default gateway and subnet mask on each PC.

Step 3: Configure the RTR02 router and enable RIP.

a.     Configure interface Fast Ethernet 0/0 using the second usable IP address in network 192.168.0.0 /24 to connect to the RTR01 router.

b.    Configure interface serial 0/0/0 using the second usable IP address in network 192.168.2.0 /24 to connect to the SVC01 router.

c.     Configure interface Fast Ethernet 0/1 using the IP address 172.17.254.254 /16.

d.    Using the no shutdown command, enable the configured interfaces.

e.     Configure RIP to advertise the networks for the configured interfaces.

f.     Configure the end devices.

·         PC2 uses the first usable IP addresses in network 172.17.0.0 /16.

·         PC3 uses the second usable IP address in network 172.17.0.0 /16.

·         Specify the appropriate default gateway and subnet mask on each PC.

Step 4: Verify the RIP configuration on each router.

a.     At the command prompt for each router, issue the commands show ip protocols and show ip route to verify RIP routing is fully converged. The show ip protocols command displays the networks the router is advertising and the addresses of other RIP routing neighbors. The show ip route command output displays all routes know to the local router including the RIP routes which are indicated by an “R”.

b.    Every device should now be able to successfully ping any other device in this activity.

c.     Click the Check Results button at the bottom of this instruction window to check your work.




No comments:

Post a Comment

Dear Reader, if you like My Blog content, feel free to comment on our blog posts.